Charge Controllers

Loom solar, Fusion 1024 charge controller - 10 amp, 12-24V

₹ 1,075INR · price may vary

Model: Fusion 1024 - lead acid
Specifications: 0

Overview

Solar Charge Controller is required to charge battery using solar panels. The other use of solar charge controller is to run DC load.

The Charge Controllers are PWM based controllers with 98% efficiency. It has USB charging Option for mobile charging & dusk to dawn feature. Dusk and down feature is used in street light application where lights is switched off in the morning and Automatically it turns on in the evening. It comes with Electronic & Software controlled protections. Maintenance Free. USB Mobile charger Output.

Product Video

Descriptions

Model Name

Fusion 1024

Manufacturer warranty

12 months

Maximum Charging current

10 Amp

Output

12 Volt / 24 Volt DC

Panel Support

200 Wp @ 12V and 400 Wp @ 24 V

Features

Automatic selection of 12V / 24V battery

0.5 amp / 5 Volt USB port for Mobile charging

Load controller with LVD & dusk to dawn feature

Technical

PWM based technology

Protections from battery deep discharge, Over charge, over load, short- circuit, wrong wiring connection.

Display

Low Battery / Fault - Red Led

Battery Charging/ Full Charged - Yellow Led

Download product user manual. to understand detailed technical product information and how to install it.

How to read this datasheet

Detailed specifications for Loom solar, Fusion 1024 charge controller - 10 amp, 12-24V have not been published yet. Loom Solar lists this charge controller in the Charge Controllers, and we add fields as the manufacturer releases them — in the meantime, ask your distributor for the datasheet before ordering.

For a charge controller, the figures that matter most are maximum PV open-circuit voltage, the hard limit that must survive cold-morning Voc rise, supported battery voltages (12/24/36/48 V) and chemistries, conversion efficiency, typically 96–99% for a good MPPT unit and whether it offers a load output, temperature compensation and remote monitoring. In any system with a battery and a separate array, the controller is what protects the most expensive component and determines how much of the array's output actually reaches storage.

Choosing a charge controller: the checks that matter

The checks below apply to any charge controller. Run them against the specification table above — most disappointing solar purchases are compatible-on-paper units that fail one of these in practice.

Prefer a unit with temperature compensation or a battery temperature sensor if the bank lives somewhere that gets hot or cold.
Choose MPPT over PWM for anything beyond a very small array. An MPPT controller harvests roughly 20–30% more energy because it converts excess panel voltage into charge current instead of throwing it away.
Size the current rating from array watts divided by battery voltage, then add at least 25% margin for cold, bright conditions where panels exceed their rated output.
Check the maximum PV input voltage against the array's Voc at your coldest expected temperature, not at 25 °C — Voc rises as temperature falls, and exceeding the limit destroys the controller instantly.

Common mistakes

Sizing on rated array watts alone and ignoring the voltage ceiling, which is the most common way controllers are killed.
Using a PWM controller with a high-voltage grid-tie panel — the voltage mismatch wastes a large share of the panel's output.
Running the load output beyond its rating instead of wiring heavy loads directly to the battery through a fuse.

Price and availability in India

Loom solar, Fusion 1024 charge controller - 10 amp, 12-24V is listed at ₹ 1,075 (INR) for India. Solar pricing moves with supply, import duties and exchange rates, and distributors set their own margins, so treat this as a comparison reference and confirm the current figure before you order.

SolarBazaar compares equipment rather than selling it. Shortlist here on specification and price, then buy from an authorised distributor or installer in India: warranty cover on solar hardware is normally honoured through the channel you bought from, so confirm who supports Loom Solar locally before ordering.

Loom solar, Fusion 1024 charge controller - 10 amp, 12-24V — frequently asked questions

How much does Loom solar, Fusion 1024 charge controller - 10 amp, 12-24V cost?

Loom solar, Fusion 1024 charge controller - 10 amp, 12-24V is listed at ₹ 1,075 (INR) for India. The figure is indicative — solar prices move with supply, duties and exchange rates, and each distributor sets its own margin — so confirm the current price with a supplier before ordering.

Who makes Loom solar, Fusion 1024 charge controller - 10 amp, 12-24V?

Loom solar, Fusion 1024 charge controller - 10 amp, 12-24V is a Loom Solar product, listed under charge controllers with model reference Fusion 1024 - lead acid. The Loom Solar brand page lists the rest of its range so you can compare across the catalogue.

Is Loom solar, Fusion 1024 charge controller - 10 amp, 12-24V right for my system?

That depends on what it has to connect to. For a charge controller, check maximum PV open-circuit voltage, the hard limit that must survive cold-morning Voc rise, supported battery voltages (12/24/36/48 V) and chemistries and conversion efficiency, typically 96–99% for a good MPPT unit against the rest of your equipment before price enters the decision. Check the maximum PV input voltage against the array's Voc at your coldest expected temperature, not at 25 °C — Voc rises as temperature falls, and exceeding the limit destroys the controller instantly.

Where can I buy Loom solar, Fusion 1024 charge controller - 10 amp, 12-24V in India?

SolarBazaar lists and compares equipment rather than selling it. Use the specifications and price here to shortlist, then buy through an authorised distributor or installer in India — buying in-channel is what keeps the manufacturer's warranty valid.

Reviews

No reviews yet

Be the first to review this product.