Charge Controllers
Charge Controllers
BrandVictron Energy
Victron Energy SmartSolar MPPT 100V 30 Amp 12/24-Volt Solar Charge Controller (Bluetooth)
$ 128.35USD · price may vary
BrandVictron Energy- Model
- SCC110030210
- Specifications
- 0
Overview
A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, SmartSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time.
SmartSolar maintains battery health, extending its life. The SmartSolar charge controller will even recharge a severely depleted battery. It can operate with a battery voltage as low as 0 Volts, provided the cells are not permanently sulphated or otherwise damaged.
Bluetooth Smart built-in
The wireless solution to set-up, monitor, update and synchronise SmartSolar Charge Controllers.
VE.Direct
For a wired data connection to a Color Control GX, other GX products, PC or other devices
Ultrafast Maximum Power Point Tracking (MPPT)
Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30 % compared to PWM charge controllers and by up to 10 % compared to slower MPPT controllers.
Advanced Maximum Power Point Detection in case of partial shading conditions
If partial shading occurs, two or more maximum power points may be present on the power-voltage curve. Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative BlueSolar algorithm will always maximize energy harvest by locking to the optimum MPP.
Outstanding conversion efficiency
No cooling fan. Maximum efficiency exceeds 98 %. The full output current up to 40 °C (104 °F).
Flexible charge algorithm
Fully programmable charge algorithm (see the software page on our website), and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details).
Extensive electronic protection
Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection.
Internal temperature sensor
Compensates absorption and float charge voltage for temperature.
Optional external battery voltage and temperature sensing via Bluetooth
A Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to communicate battery voltage and temperature to one or more SmartSolar Charge Controllers.
Fully discharged battery recovery function
Will initiate charging even if the battery has been discharged to zero volts. Will reconnect to a fully discharged Li-ion battery with integrated disconnect function.
Specifications
Battery voltage: 12/24V Auto Select
Rated charge current: 30A
Nominal PV Power, 12V 1a,b): 440W
Nominal PV Power, 24V 1a,b): 880W
Maximum PV open circuit voltage: 100V
Max. PV short circuit current 2): 35A
Maximum efficiency: 98%
Weight: 1.3kg
Dimensions (hxwxd): 130 x 186 x 70mm
Still Have Questions About Victron Energy SmartSolar? Give us a call today 1-877-242-2792
Reading the specifications
Detailed specifications for Victron Energy SmartSolar MPPT 100V 30 Amp 12/24-Volt Solar Charge Controller (Bluetooth) have not been published yet. Victron Energy lists this charge controller in the Charge Controllers, and we add fields as the manufacturer releases them — in the meantime, ask your distributor for the datasheet before ordering.
For a charge controller, the figures that matter most are supported battery voltages (12/24/36/48 V) and chemistries, conversion efficiency, typically 96–99% for a good MPPT unit, whether it offers a load output, temperature compensation and remote monitoring and type: MPPT or PWM. In any system with a battery and a separate array, the controller is what protects the most expensive component and determines how much of the array's output actually reaches storage.
Choosing a charge controller: the checks that matter
The checks below apply to any charge controller. Run them against the specification table above — most disappointing solar purchases are compatible-on-paper units that fail one of these in practice.
- Choose MPPT over PWM for anything beyond a very small array. An MPPT controller harvests roughly 20–30% more energy because it converts excess panel voltage into charge current instead of throwing it away.
- Size the current rating from array watts divided by battery voltage, then add at least 25% margin for cold, bright conditions where panels exceed their rated output.
- Check the maximum PV input voltage against the array's Voc at your coldest expected temperature, not at 25 °C — Voc rises as temperature falls, and exceeding the limit destroys the controller instantly.
- Confirm the controller supports your battery chemistry with the right charge profile. Lithium, AGM, gel and flooded batteries need different absorption and float voltages.
Where buyers lose money
- Sizing on rated array watts alone and ignoring the voltage ceiling, which is the most common way controllers are killed.
- Using a PWM controller with a high-voltage grid-tie panel — the voltage mismatch wastes a large share of the panel's output.
- Running the load output beyond its rating instead of wiring heavy loads directly to the battery through a fuse.
Price and availability in Canada
Victron Energy SmartSolar MPPT 100V 30 Amp 12/24-Volt Solar Charge Controller (Bluetooth) is listed at $ 128 (USD) for Canada. Solar pricing moves with supply, import duties and exchange rates, and distributors set their own margins, so treat this as a comparison reference and confirm the current figure before you order.
SolarBazaar compares equipment rather than selling it. Shortlist here on specification and price, then buy from an authorised distributor or installer in Canada: warranty cover on solar hardware is normally honoured through the channel you bought from, so confirm who supports Victron Energy locally before ordering.
Victron Energy SmartSolar MPPT 100V 30 Amp 12/24-Volt Solar Charge Controller (Bluetooth) — frequently asked questions
How much does Victron Energy SmartSolar MPPT 100V 30 Amp 12/24-Volt Solar Charge Controller (Bluetooth) cost?
Victron Energy SmartSolar MPPT 100V 30 Amp 12/24-Volt Solar Charge Controller (Bluetooth) is listed at $ 128 (USD) for Canada. The figure is indicative — solar prices move with supply, duties and exchange rates, and each distributor sets its own margin — so confirm the current price with a supplier before ordering.
Who makes Victron Energy SmartSolar MPPT 100V 30 Amp 12/24-Volt Solar Charge Controller (Bluetooth)?
Victron Energy SmartSolar MPPT 100V 30 Amp 12/24-Volt Solar Charge Controller (Bluetooth) is a Victron Energy product, listed under charge controllers with model reference SCC110030210. The Victron Energy brand page lists the rest of its range so you can compare across the catalogue.
Is Victron Energy SmartSolar MPPT 100V 30 Amp 12/24-Volt Solar Charge Controller (Bluetooth) right for my system?
That depends on what it has to connect to. For a charge controller, check whether it offers a load output, temperature compensation and remote monitoring, type: MPPT or PWM and rated charge current in amps, which must exceed the array's short-circuit current with margin against the rest of your equipment before price enters the decision. Confirm the controller supports your battery chemistry with the right charge profile. Lithium, AGM, gel and flooded batteries need different absorption and float voltages.
Where can I buy Victron Energy SmartSolar MPPT 100V 30 Amp 12/24-Volt Solar Charge Controller (Bluetooth) in Canada?
SolarBazaar lists and compares equipment rather than selling it. Use the specifications and price here to shortlist, then buy through an authorised distributor or installer in Canada — buying in-channel is what keeps the manufacturer's warranty valid.
Reviews
No reviews yet
Be the first to review this product.
Write a Review
Share your experience — no account needed.
